Product Carousel Tabs
Bestsellers
Smartphones
-
Acrylics / Resin, Laboratory, Laboratory Material
Meliodent Heat Cure
Meliodent – Cost-Effective Production Of Dentures
A denture base material designed by Heraeus Kulzer to make technicians working environment safer. By containing only organic pigments. Meliodent is free from cadmium. The surfance of the denture has perfect properties that allows excellent oral hygiene.
The large variety of colours satisfies almost all needs. Whether clear, standard pink or exotic colours – almost all regional colour exceptions can be satisfied. Compared to other products, Meliodent Heat Cure plays a special role as a denture material : it is most probably the only material with such a large variety of colours!
Benefits at a glance :
- Super fine polymer gives a superb flow
- Short dough time 6 minutes at 23°C
- Long working time up to 30 minutes plus (depends on room temperature)
- Economical for use in the dental laboratory
- Unique co-polymer formula
- Broad spectrum of colour shades to suit all patients
- Exceptional smooth surface
Features Benefits Meliodents super-fine polymer gives a superb flow Trial closures may become unnecessary; displaced teeth and raised bite during flasking can be a thing of the past Meliodent has a short dough time 6 minutes at 23°C Allows the busy technician to save time by packing dentures earlier than with other acrylics Meliodent has a long working time up to 30 minutes plus (depends on room temperature) High versatile working – Can be cured using the boiling technique or by any other curing cycle Meliodent is economical priced for use in the dental laboratory A superior product with a competitive edge Meliodent has a unique co-polymer formula This gives exceptional surface and smoothness characteristics. Less plaque build up and superior tissue compatibility means healthier patients
SKU: n/a -
Acrylics / Resin, Laboratory, Laboratory Material
Paladent 20
Dental acrylic for fabrication of full and partial dentures
Paladent 20 – its well-balanced properties make it economical to use and guarantee high-quality dentures at a reasonable price.
Paladent 20 has very good mechanical properties. It can be processed easily without additional equipment. It’s plastic consistency allows the dough to be packed very easily. In addition, it has a very long working time of up to 30 min, allowing the production of several dentures simultaneously.
Paladent 20 has a good colour stability and a low residual monomer. These points guarantee that the patient can wear the denture for many years without any problems. The colours such as R50 veined are excellent colour matches to all other Heraeus Kulzer denture materials while R50 veined allows individual choice of colour, invisible repairs and extensions.
- Long working time up to 30 minutes (depends on room temperature)
- Superiour mechanical properties
- Excellent colour stability and low residual monomer
- Economical for use in the dental laboratory
- Exceptional smooth surface
SKU: n/a -
Acrylics / Resin, Laboratory, Laboratory Material
Meliodent Rapid Repair
Meliodent – Cost-Effective Production Of Dentures
An additional component is Meliodent Rapid Repair, an acrylic used for repairs, with material and colour properties that suit this top quality denture base material perfectly.
- An economical advantage for use in the dental laboratory
- Broad spectrum of colour shades to suit all patients
- Short polymerisation time (ten minutes)
SKU: n/a -
Acrylics / Resin, Laboratory, Laboratory Material
Dentalon Plus
DENTALON® Plus – well-established
Dentalon Plus is a well-established self-curing resin in a powder/liquid combination for the fabrication of temporary crowns and bridges.
- High gloss polish
- High mechanical stability
- Individual colour adaptation possible
- High colour stability due to amine free catalyst system
SKU: n/a
Laptops & Computers
-
Acrylics / Resin, Laboratory, Laboratory Material
Meliodent Heat Cure
Meliodent – Cost-Effective Production Of Dentures
A denture base material designed by Heraeus Kulzer to make technicians working environment safer. By containing only organic pigments. Meliodent is free from cadmium. The surfance of the denture has perfect properties that allows excellent oral hygiene.
The large variety of colours satisfies almost all needs. Whether clear, standard pink or exotic colours – almost all regional colour exceptions can be satisfied. Compared to other products, Meliodent Heat Cure plays a special role as a denture material : it is most probably the only material with such a large variety of colours!
Benefits at a glance :
- Super fine polymer gives a superb flow
- Short dough time 6 minutes at 23°C
- Long working time up to 30 minutes plus (depends on room temperature)
- Economical for use in the dental laboratory
- Unique co-polymer formula
- Broad spectrum of colour shades to suit all patients
- Exceptional smooth surface
Features Benefits Meliodents super-fine polymer gives a superb flow Trial closures may become unnecessary; displaced teeth and raised bite during flasking can be a thing of the past Meliodent has a short dough time 6 minutes at 23°C Allows the busy technician to save time by packing dentures earlier than with other acrylics Meliodent has a long working time up to 30 minutes plus (depends on room temperature) High versatile working – Can be cured using the boiling technique or by any other curing cycle Meliodent is economical priced for use in the dental laboratory A superior product with a competitive edge Meliodent has a unique co-polymer formula This gives exceptional surface and smoothness characteristics. Less plaque build up and superior tissue compatibility means healthier patients
SKU: n/a -
Acrylics / Resin, Laboratory, Laboratory Material
Paladent 20
Dental acrylic for fabrication of full and partial dentures
Paladent 20 – its well-balanced properties make it economical to use and guarantee high-quality dentures at a reasonable price.
Paladent 20 has very good mechanical properties. It can be processed easily without additional equipment. It’s plastic consistency allows the dough to be packed very easily. In addition, it has a very long working time of up to 30 min, allowing the production of several dentures simultaneously.
Paladent 20 has a good colour stability and a low residual monomer. These points guarantee that the patient can wear the denture for many years without any problems. The colours such as R50 veined are excellent colour matches to all other Heraeus Kulzer denture materials while R50 veined allows individual choice of colour, invisible repairs and extensions.
- Long working time up to 30 minutes (depends on room temperature)
- Superiour mechanical properties
- Excellent colour stability and low residual monomer
- Economical for use in the dental laboratory
- Exceptional smooth surface
SKU: n/a -
Acrylics / Resin, Laboratory, Laboratory Material
Meliodent Rapid Repair
Meliodent – Cost-Effective Production Of Dentures
An additional component is Meliodent Rapid Repair, an acrylic used for repairs, with material and colour properties that suit this top quality denture base material perfectly.
- An economical advantage for use in the dental laboratory
- Broad spectrum of colour shades to suit all patients
- Short polymerisation time (ten minutes)
SKU: n/a -
Acrylics / Resin, Laboratory, Laboratory Material
Dentalon Plus
DENTALON® Plus – well-established
Dentalon Plus is a well-established self-curing resin in a powder/liquid combination for the fabrication of temporary crowns and bridges.
- High gloss polish
- High mechanical stability
- Individual colour adaptation possible
- High colour stability due to amine free catalyst system
SKU: n/a
Laptops & Computers
Smartphones
Meliodent Heat Cure
Meliodent – Cost-Effective Production Of Dentures
A denture base material designed by Heraeus Kulzer to make technicians working environment safer. By containing only organic pigments. Meliodent is free from cadmium. The surfance of the denture has perfect properties that allows excellent oral hygiene.
The large variety of colours satisfies almost all needs. Whether clear, standard pink or exotic colours – almost all regional colour exceptions can be satisfied. Compared to other products, Meliodent Heat Cure plays a special role as a denture material : it is most probably the only material with such a large variety of colours!
Benefits at a glance :
Features | Benefits |
---|---|
Meliodents super-fine polymer gives a superb flow | Trial closures may become unnecessary; displaced teeth and raised bite during flasking can be a thing of the past |
Meliodent has a short dough time 6 minutes at 23°C | Allows the busy technician to save time by packing dentures earlier than with other acrylics |
Meliodent has a long working time up to 30 minutes plus (depends on room temperature) | High versatile working – Can be cured using the boiling technique or by any other curing cycle |
Meliodent is economical priced for use in the dental laboratory | A superior product with a competitive edge |
Meliodent has a unique co-polymer formula | This gives exceptional surface and smoothness characteristics. Less plaque build up and superior tissue compatibility means healthier patients |
Paladent 20
Dental acrylic for fabrication of full and partial dentures
Paladent 20 – its well-balanced properties make it economical to use and guarantee high-quality dentures at a reasonable price.
Paladent 20 has very good mechanical properties. It can be processed easily without additional equipment. It’s plastic consistency allows the dough to be packed very easily. In addition, it has a very long working time of up to 30 min, allowing the production of several dentures simultaneously.
Paladent 20 has a good colour stability and a low residual monomer. These points guarantee that the patient can wear the denture for many years without any problems. The colours such as R50 veined are excellent colour matches to all other Heraeus Kulzer denture materials while R50 veined allows individual choice of colour, invisible repairs and extensions.
Meliodent Rapid Repair
Meliodent – Cost-Effective Production Of Dentures
An additional component is Meliodent Rapid Repair, an acrylic used for repairs, with material and colour properties that suit this top quality denture base material perfectly.
Dentalon Plus
DENTALON® Plus – well-established
Dentalon Plus is a well-established self-curing resin in a powder/liquid combination for the fabrication of temporary crowns and bridges.
Denture Liner
Denture Liner
Economical lining material with less stimulation, and with hardness same as the denture base
This is the hard lining material with less stimulation and hardens gradually, so that it can be taken out safely even in the case of many undercuts for partial dentures. Also by using attached self-curing accelerator, it can be as hard as the base of denture. Therefore there will be little level difference between the base and lining material at the final polish.
Contents | Powder 100 gr, liquid 100 mL, self-curing accelerator 36 gr |
Colors | Pink |
Denture Soft II
Denture Soft II
Best selling product with outstanding durability
In addition to durability, this conditioner is twice as good as a conventional one, the durability has further increased due to attached surface smoothing material
Contents | Powder 100 gr, liquid 80 mL, New top coat 6 mL |
Colors | Pink |
FD Soft
FD Soft
Acrylic soft lining material as soft as tissue conditioner
Durability is six months to a year by using with a denture cleanser Clean Soft for exclusive use.
A denture cleanser exclusively for soft lining material, “Clean Soft” should be used to prevent a lining surface of the denture from being ruined.
Acrylic soft lining material has many merits;
A denture cleanser exclusively for soft lining material, “Clean Soft” should be used to prevent a lining surface of the denture from being
Contents | Powder 110 gr, liquid 100 mL, New top coat 30 mL |
Colors | Pink |
Soft To Hard DIL
Soft To Hard DIL
The world first success in the development.
This functions as tissue conditioner first, then automatically begins self-curing a week after wearing. As it hardens after taking the functional impression, so patients feel comfortable with their denture with less pain. “Polident” with enzyme (denture cleanser) can be used from a week after wearing.
Contents | Powder 50 gr, liquid 45 mL, New top coat 30 mL |
Colors | Pink, Fiber Pink |
Peri-Resin II
Peri-Resin II
Only this resin which can make border molding and sealing of dentures
Because of its thixotropic character, border molding is easy in the early polymerizing stage.
As Peri-Resin is not sticky, so you can shape the border easily with wet fingers.
After extending and correcting the shape of peripheral edge of denture base, mucous surface might be lined using lining material such as DIL.
Contents | Powder 70 gr, liquid 50 mL, New top coat 6 ml, Syringe 2 |
Colors | Pink |
Clean Soft
Clean Soft
Denture cleanser exclusively for soft resin and durability of soft lining material has increased greatly.
This is a denture cleanser exclusively for acrylic soft lining material.
The cleaning strength is ten times stronger than that of commercially available enzymatic ones.
Length | 1,25 metre |
---|---|
Length | 1,25 metre |
Length | 1,25 metre |
Length | 1,25 metre |
Replica
Replica
Replica of denture can be made easily at chair side
This is a special resin exclusively for replica denture, which suppresses a resin contraction, increases a fitting accuracy, and gets smooth surface. Replica denture can be made easily with a flask for exclusively use and alginate impression material.
Poly Seal
Poly Seal
Fit for temporary sealing of cavity which easily comes out
Characteristics :
Contents | Powder 100 gr, Powder 250 gr Liquid 100 mL, Liquid 300 ml |
Colors | Ivory |
Snap
Snap
Total cost down with this quick self-curing resin
Self-curing resin of quick hardening comes in two colors, which are crown and gingival color.
It can be used for repair of denture and temporary crown.
Contents | Powder 100 gr, Powder 250 gr Liquid 80 mL, Liquid 300 ml |
Colors | Pink, Fiber Pink, Ivory |
Denture Gel
Denture Gel
Oral moisturizing paste suitable to patients with dentures
This oral mucosa moisturizing paste has more viscosity than conventional products, so that patients with dentures can use for denture stability. There is a small pouch type for easy carrying.
Type | Contents |
---|---|
Tube | 45 gr |
Small Pouch | 2,5 gr |
Nu Alloy ® Dp Active
Nu Alloy ® Dp Active
Nu Alloy ® dp Active is a unique or simple composition alloy, which guarantees absolute chemical homogeneity of their particles. Thanks to ideal chemical composition (45% Ag, 31% Sn and 24% Cu), eliminating the presence of gamma-2 phase of the microstructure of the amalgam due of the high copper content. This reduces the problems of fragility and instability in corrosive environments.
Nu Alloy ® Dp
Nu Alloy ® Dp
Dispersed-phase : A mixture of lathe-cut irregular particles and atomized spherical particles.
High-copper-content: >12%.
Nu Alloy® dp is a single composition alloy with absolute homogeneity of its particles.
Thanks to its optimal chemical composition (45%Ag, 31%Sn, and 24%Cu) and its high copper content, the gamma-2 phase is eliminated from the alloy microstructure. As a result of this, fragility and instability problems in corrosive environments decrease.
Its morphology is composed of atomized and lathe-cut particles which results in a fast amalgamation with its optimal 50% mercury content (Mercury-to-alloy ratio : 1:1) and improves the alloy’s physical and mechanical properties.
This alloy has a high resistance to marginal fractures, excellent adaptation and marginal sealing, thanks to the homogeneity of its particles.
Fine surface finish originated in the granulometry of its spherical and prismatic particles.
Recently Viewed
NIS-SIM Simulator
A practical solution for preclinical training
Allows students to practice basic and advanced preclinical skills in a clinical-like environment. Gives access to a wide range of training situations using various NISSIN dental training models.
Operating environment | Temperature: 5???40????/ Relative humidity: 30%???80% | ||
Power source | 100/220V±10% / 50/60Hz | ||
Input air pressure | 0.55MPa???0.7MPa (Internal pressure 0.5MPa±0.02MPa) | ||
Water pressure | Not exceeding 0.22MPa | ||
Dimensions | Operation position: 1,040(L)×400(W)×710???860[1](H) mm (Housing height: 480 mm) Storing position: 620(L)×400(W)×1030(H) mm |
||
Weight | Approx. 50 kg | ||
Height adjustment range | 150 mm ± 2mm | ||
Phantom tilt range | -5° to +85° from horizontal plane |
Due to product improvement, product specifications and design may change without prior notice.
Prosthetic Restoration Jaw Model (32 teeth) [CON2001-UL-HD-FEM-32]
Prosthetic Restoration Jaw Model (32 teeth) [CON2001-UL-HD-FEM-32]
Inverted Cone Hollow 9504F Polishers & Brushes
Inverted Cone Hollow 9504F Polishers & Brushes
9504F | inverted cone hollow | ||
---|---|---|---|
Fig | Shank | ISO | Ø |
Right Angle | |||
9504F | RA | 653 204 030 503 – | 060 |
L mm | 9,5 | ||
Content | 5 |
NobelDirect 3.0
NobelDirect 3.0
The NobelDirect 3.0 implant encompasses the osseous component and restorative component in one piece. This design is based on the One-Stage Placement concept and offers a number of possible advantages :
Treatment Planning
Indication for use
The diameter of two-piece implants is limited due to the lesser strength of the hollow implant body and the screwjoint. The one-piece design overcomes this limitation and allows us to offer a special small diameter implant – NobelDirect 3.0. This implant is intended for use in the tight space challenges in the region of the mandibular central and lateral incisors and maxillary lateral incisors with a delayed loading protocol.
When the implant is placed it should be restored with a Healing Cap or temporary crown without occlusal loading during the healing time.
Inclusion / Exclusion criteria
The following criteria are recommended for the use of NobelDirect 3.0
The treatment plan should identify and reduce potential load factors such as lateral occlusal contacts, unstable dental occlusion and severe bruxism or other pronounced parafunctions.
Pretreatment Considerations
Radiographic Examinations
Implant templates that are actual size or magnified 130% or 170% are supplied for NobelDirect 3.0 and used in conjunction with radiographic imaging as a guide to selecting the proper implant to be used. These overlays are to be used as guides only. When more accurate measurements are required, radiographic techniques such as tomograms and computerized tomographic (CT) scans should be utilized.
Additional diagnostic radiographic imaging may be indicated to determine the quality and quantity of alveolar bone or to identify anatomical landmarks.
Implant placement with Flap Reflection
A flap approach is recommended if adequate bone has not been confirmed, if direct vision of anatomic landmarks is necessary or if the facial gingival surface needs connective tissue augmentation.
Implant placement immediately after extraction
The healing capacity of an extraction site is excellent and, as long as the initial stability is reached, implant therapy is well suited to extraction sites. In addition to the above criteria, careful removal of any soft tissue and / or infected tissue is required. If periodontitis is the cause of the extraction, healing before implant treatment is often the procedure of choice.
The following steps are recommended for placement at time of extraction :
Flapless Implant Placement
Flapless surgery is indicated in situations where adequate bone and attached gingiva are present, as well as sufficient vestibular depth.
Note: Available bone and significant anatomical landmarks such as blood vessels, nerves and concavities have to be confirmed with conventional diagnostic tools such as radiographic imaging, probing and palpation.