Shop
Showing 2401–2430 of 2509 results
-
Instruments, Miscellaneous, Restorative Dentistry Instruments
Universal & Other Ring Placement Forceps
Instruments, Miscellaneous, Restorative Dentistry InstrumentsUniversal & Other Ring Placement Forceps
The Ring Placement Forceps have been designed specifically to fit all Garrison rings. They grasp the rings securely and provide ample force to open the rings. With an updated grip, the forceps easily spread the rings with less hand fatigue, even over large molars. Some rubber dam clamp forceps will not open the rings far enough to allow for proper placement.We also offer Universal forceps with a patent pending tip design that works with all currently available sectional matrix rings and rubber dam clamps.
SKU: n/a -
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area Models
Universal Cannula III
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area ModelsUniversal Cannula III
Universal Cannula III for adults
The universal cannula III is particularly quiet.
In a study by the Fraunhofer Institute, the measured volume was significantly below the level of comparable competitor products. It provides tested, low-noise aspiration of spray mist. And that without having to leave the pressure points.
- Proven reduction of the germ-laden aerosol cloud
- 30% lower noise level during suction – confirmed by expert assessment
- No corners or sharp edges – comfortable in the patient's mouth
- Stylish colours, to match every surgery interior
Universal Cannula III optionally with pluggable auxiliary air sleeve
SKU: n/a -
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area Models
Universal Cannula Petito
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area ModelsUniversal Cannula Petito
Universal Cannula Petito for children
Children require a highly functional cannula that permits ergonomic treatment.
The Universal Cannula Petito is just as quiet and tested as the Universal Cannula III, but much smaller. It also has no corners or edges and leaves no sore spots.
- Universal Cannula Petito with integrated auxiliary air intakes on the shaft
- Proven reduction of the germ-laden aerosol cloud
- 30 % lower noise level during suction – confirmed by expert assessment
- No corners or sharp edges – comfortable in the patient's mouth
- Stylish colours to match every surgery interior
SKU: n/a -
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area Models
Universal Cannula Protect
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area ModelsUniversal Cannula Protect
Universal Cannula Protect against reflux
Secondary air inlets may prevent a reflux of contaminated secretions from the suction system during the suction process of the cannula.
The special feature :
Even with the inlets, Protect cannulas are particularly quiet.
- New Universal Cannula Protect with integrated secondary air inlets on the shaft
- Proven reduction of the germ-laden aerosol cloud
- 30 % lower noise level during suction – confirmed by expert assessment
- No corners or sharp edges – comfortable in the patient's mouth
SKU: n/a -
Instruments, Miscellaneous, Restorative Dentistry Instruments
Universal Composite Instrument
Our titanium nitride Composite Instruments have been carefully designed to provide the most streamlined and versatile instrument assortment for composite restorations.
- The titanium nitride coating is 40% harder than stainless steel and testing has proven it to be the best nonstick surface for placement, shaping and carving of composites.
- Our special coating process withstands diverse cleaning and sterilization methods, including ultrasonic cleaning.
- Lightweight large-diameter stainless steel handles provide improved ergonomics and precise control for delicate contouring and shaping.
Titanium tough guarantee! Our instruments are 100% guaranteed to work better than any other composite instruments you have ever used. If you are not completely satisfied, return them within six months for a full refund.
TN008 Universal Composite Instrument
SKU: n/a -
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area Models
Universal Dispenser
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area ModelsUniversal Dispenser
Dimensions (WxHxD) : S 400 / L 400: 8.2 x 24.5 x 8.2 cm, arm lever length: S: 16 cm, L: 21.5 cm, L 1000: 9.2 x 29 x 9 cm
Arm lever length : 22.5 cm
Available as : S 400 and L 400 for 500 ml bottle, L 1000 for 800 ml bottle
Our recommendation : HD 410, HD 412 essential, HD 435, HD 440 in 500 ml bottle or 800 ml bottle
Universal, wall-mounted dispenser for hand preparations.
- Extremely user-friendly
- Available with short (S) or long (L) arm lever
- Durable aluminium and stainless steel design
- Autoclavable pumpe
SKU: n/a -
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area Models
Universal Torque Wrench Torq Control
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area ModelsUniversal Torque Wrench Torq Control
The success of the implant treatment depends on the precise tightening of the parts placed directly on the implant. A pre-stressed tightening of the screw will help avoid any risk of screw loosening. Also, high tightening torques may lead to screw fracture. A calibrated tightening can only be guaranteed through the use of a precision instrument offering a torque control system.
The dynamometrical manual wrench *Torq Control® has been specially designed to meet those requirements.
Main advantages of Torq Control®:
- Universal torque wrench, recommended with any type of implants
- Perfect control of torque thanks to 7 torques values (10/15/20/25/30/32/35N.cm)
- Automatic declutching for optimum security
- Only 135 gr for a better freedom of movement
- Optimized access in mouth thanks to the micro-head
- 100° angulated micro-head for easy access in mouth (posterior areas)
- One piece design with smooth surface to limit bacterial retention
*mandrel not supplied
SKU: n/a -
Impression Material, Materials / Medicament
Universal VPS Adhesive
Universal vinyl polysiloxane adhesive to assist bonding of VPS impression material to the tray to ensure accurate impressions.
- Coat all impression trays (including perforated and custom trays)
- Prevent pull-away and distortion during impression removal
SKU: n/a -
Luting Cement & Liners, Materials / Medicament
Urbical
Self-curing calcium hydroxide
Urbical is a self-curing calcium hydroxide paste / paste system with a flowable consistency.
The material is indicated for indirect pulp capping and as a cavity liner under all filling materials.
The product is easy to apply and allows a sufficient working time as well as a short setting time in the mouth. Urbical is highly radiopaque as well as bacteriostatic.
Due to its comparably high pH-value Urbical is acid resistant and thus provides excellent pulp protection.
- Easy to mix and to apply
- Sufficient working time and short setting in the mouth
- High radiopacity for a good diagnostic control
- Contains 26% calcium hydroxide: activates the formation of secondary dentine
- Recovering of the pulp – preservation of vitality
- Bacteriostatic
- High pH-value (11.3)
- Strongly acid resistant
SKU: n/a -
Luting Cement & Liners, Materials / Medicament
Urbical LC
Light-curing radiopaque calcium hydroxide
Urbical LC is a light-curing calcium hydroxide paste, suitable for indirect pulp capping and as a cavity liner under all filling materials.
The product convinces by a significantly higher compressive strength than conventional calcium hydroxides possess and thus reduces the risk of filling fractures.
- For indirect pulp capping
- For linings under all filling materials
SKU: n/a -
-
Equipment / Dental Unit / X-Ray / Etc, Suction
V 1200 S
The dry V Suction Systems
Up to 6 treatment positions, with 4 operators working simultaneously 400 V 3 ∼, 50 Hz, with condensate separator and control unit 400 V 3 ∼ // 24 V ∼
Sophisticated technology with convincing suction power.
High-quality, robust drive motors, reliable continuous operation, great suction power within seconds, and flexible installation options.
Amazing power
The dry air suction systems by Dürr Dental are extremely powerful yet run really quietly. The V suction units are called dry systems because the aspirated substances are quickly guided into a separation/amalgam elimination unit. These components are integrated into the Dental Unit. Only dry air reaches the suction unit.
Seven to eight hours of continuous operation are not unusual. This places high demands on the technology. Dürr Dental V suction machines fulfil these requirements tirelessly. The contact-free, rotating turbine wheels generate the required vacuum and flow rate (suction power). A reliable electric motor enables non-stop operation. To reliably protect against condensated water, all models are fitted with a condensate separator as standard.
Model V 1200 S Voltage (V 3~) 400 Frequency (Hz) 50 Current consumption (A) 3.6 Power (kW) 2 Dimensions without condensate separator (H x W x D cm) 52 x 41 x 42 Dimensions with condensate separator (H x W x D cm) 57 x 62 x 42 Dimensions with housing (H x W x D cm) 55 x 49 x 53 Vacuum (mbar) AAV 1) 170 Weight without housing (kg) 32 Weight with housing (kg) 48 Noise level 2) without housing dB(A) approx. 66 Noise level 2) with housing dB(A) approx. 59 1) AAV = auxiliary air valve
2) The noise level is influenced by the room in which the system is installed. In a reverberant room (e.g. with tiled walls) the noise level may be higher.
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 12000
Clinic Suction System
Group with 4 suction machines incl. control unit with vacuum controller and 1 bacteria filter, remote monitoring possible.
For up to 70 workplaces with max. 40 operators at the same time.
Flexible solutions to meet your needs
Dürr Dental offers vacuum systems for dry and semi-dry suction systems. The flexible solutions are available in 6 variants and suitable for up to 100 treatment units. The integrated exhaust air bacteria filter only has to be changed every 3,500 hours. The power side channel compressors are precisely adjusted to the requriements by the intelligent PLC system.
High reliability, low power consumption
A sensor switches the custion motors on and off as required, allowing efficient use to be made of the electrical energy. The PLC system controls the equal use of the V machines, increasing their overall service lie and reliability. An electrical and mechanical auxiliary air valve provides additional cooling for the motots and a constant suction power.
Everything's under control thanks to the PLC system
Which suction motor is running? Momentary vacuum? Bakteria filter change? These questions are answered for the technician by the clinic display in the intelligent programmable logic controller. This allows him to monitor the complete suction or compressed air system at any time and to easily detect faults. The visualisation system from Dürr Dental even allows all the clinic systems to be remotely monitored.
Model V 12000 Voltage (V 3~) 400 Frequency (Hz) 50 / 60 Electrical power (kW) 10,8 / 14,4 Current consumption (A) 21,1 / 25,1 Dimensions (H x W x D cm) 180 x 130 x 130 Space requirements (H x W x D cm) 180 x 230 x 230 Weight (kg) 335 Vacuum (mbar) 160 Noise level dB(A) 76 without housing, 63 with housing Suction exhaust air connection (mm) 2x 110 and 1x 160
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 15000
Clinic Suction System
Group with 5 suction machines incl. control unit with vacuum controller and 2 bacteria filters, remote monitoring possible.
For up to 80 workplaces with max. 50 operators at the same time.
Flexible solutions to meet your needs
Dürr Dental offers vacuum systems for dry and semi-dry suction systems. The flexible solutions are available in 6 variants and suitable for up to 100 treatment units. The integrated exhaust air bacteria filter only has to be changed every 3,500 hours. The power side channel compressors are precisely adjusted to the requriements by the intelligent PLC system.
High reliability, low power consumption
A sensor switches the custion motors on and off as required, allowing efficient use to be made of the electrical energy. The PLC system controls the equal use of the V machines, increasing their overall service lie and reliability. An electrical and mechanical auxiliary air valve provides additional cooling for the motots and a constant suction power.
Everything's under control thanks to the PLC system
Which suction motor is running? Momentary vacuum? Bakteria filter change? These questions are answered for the technician by the clinic display in the intelligent programmable logic controller. This allows him to monitor the complete suction or compressed air system at any time and to easily detect faults. The visualisation system from Dürr Dental even allows all the clinic systems to be remotely monitored.
Model V 15000 Voltage (V 3~) 400 Frequency (Hz) 50 / 60 Electrical power (kW) 13,4 / 17,9 Current consumption (A) 26,6 / 30,6 Dimensions (H x W x D cm) 180 x 130 x 130 Space requirements (H x W x D cm) 180 x 230 x 230 Weight (kg) 375 Vacuum (mbar) 160 Noise level dB(A) 77 without housing, 65 with housing Suction exhaust air connection (mm) 2x 110 and 1x 160
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 18000
Clinic Suction System
Group with 6 suction machines incl. control unit with vacuum controller and 2 bacteria filters, remote monitoring possible.
For up to 100 workplaces with max. 60 operators at the same time.
Flexible solutions to meet your needs
Dürr Dental offers vacuum systems for dry and semi-dry suction systems. The flexible solutions are available in 6 variants and suitable for up to 100 treatment units. The integrated exhaust air bacteria filter only has to be changed every 3,500 hours. The power side channel compressors are precisely adjusted to the requriements by the intelligent PLC system.
High reliability, low power consumption
A sensor switches the custion motors on and off as required, allowing efficient use to be made of the electrical energy. The PLC system controls the equal use of the V machines, increasing their overall service lie and reliability. An electrical and mechanical auxiliary air valve provides additional cooling for the motots and a constant suction power.
Everything's under control thanks to the PLC system
Which suction motor is running? Momentary vacuum? Bakteria filter change? These questions are answered for the technician by the clinic display in the intelligent programmable logic controller. This allows him to monitor the complete suction or compressed air system at any time and to easily detect faults. The visualisation system from Dürr Dental even allows all the clinic systems to be remotely monitored.
Model V 18000 Voltage (V 3~) 400 Frequency (Hz) 50 / 60 Electrical power (kW) 16,0 / 21,4 Current consumption (A) 30,1 / 36,1 Dimensions (H x W x D cm) 180 x 130 x 130 Space requirements (H x W x D cm) 180 x 230 x 230 Weight (kg) 415 Vacuum (mbar) 160 Noise level dB(A) 78 without housing, 66 with housing Suction exhaust air connection (mm) 2x 110 and 1x 160
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 2400
Clinic Suction Systems
Maximum performance for 8 therapists
The V 2400 suction machine is employed in the dry suction system.
Here the principle :
Of short transport routes for the intaken substances applies. Separation is integrated into the treatment unit and dry, clean air routes to the suction machine.
- Allows 14 treatment stations to be served
- Up to 8 operators at the same time
- Delivery is made installed on a floor installation console
- 2 condensate separators with preinstalled control cabinet
Flexible solutions to meet your needs
Dürr Dental offers vacuum systems for dry and semi-dry suction systems. The flexible solutions are available in 6 variants and suitable for up to 100 treatment units. The integrated exhaust air bacteria filter only has to be changed every 3,500 hours. The power side channel compressors are precisely adjusted to the requriements by the intelligent PLC system.
High reliability, low power consumption
A sensor switches the custion motors on and off as required, allowing efficient use to be made of the electrical energy. The PLC system controls the equal use of the V machines, increasing their overall service lie and reliability. An electrical and mechanical auxiliary air valve provides additional cooling for the motots and a constant suction power.
Everything's under control thanks to the PLC system
Which suction motor is running? Momentary vacuum? Bakteria filter change? These questions are answered for the technician by the clinic display in the intelligent programmable logic controller. This allows him to monitor the complete suction or compressed air system at any time and to easily detect faults. The visualisation system from Dürr Dental even allows all the clinic systems to be remotely monitored.
Model V 2400 Voltage (V 3~) 400 Frequency (Hz) 50/60 Current consumption (A) 5.6/6.8 Power (kW) 3.3/4.4 Dimensions (H x W x D cm) 115 x 90 x 48 Weight (kg) approx. 65 Fuse ratings (AT) 16 Medical product class IIa
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 300 S
The dry V Suction Systems
For 1 operator 230 V 1, 50 Hz, with condensate separator and control electronics 230 V 1 ∼ // 24 V ∼
Sophisticated technology with convincing suction power.
High-quality, robust drive motors, reliable continuous operation, great suction power within seconds, and flexible installation options.
Amazing power
The dry air suction systems by Dürr Dental are extremely powerful yet run really quietly. The V suction units are called dry systems because the aspirated substances are quickly guided into a separation/amalgam elimination unit. These components are integrated into the Dental Unit. Only dry air reaches the suction unit.
Seven to eight hours of continuous operation are not unusual. This places high demands on the technology. Dürr Dental V suction machines fulfil these requirements tirelessly. The contact-free, rotating turbine wheels generate the required vacuum and flow rate (suction power). A reliable electric motor enables non-stop operation. To reliably protect against condensated water, all models are fitted with a condensate separator as standard.
Model V 300 S Voltage (V 1~) 230 Frequency (Hz) 50/60 Current consumption (A) 2.9/3.7 Power (kW) 0.58/0.8 Speed (rpm) 2,850 Vacuum (mbar) without AAV 180 Cyclic duration factor (S1) 100% Noise level dB(A) approx. 63, with housing approx. 54 Dimensions (H x W x D cm) 37 x 31 x 31
43 x 38 x 43 (with condensate separator)
51 x 36 x 36 (with housing)Weight (kg) 12.5, with housing 20
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 600
The dry V Suction Systems
Up to 3 treatment positions, with 2 operators working simultaneously 230 V 1 ∼ , 50 Hz, with condensate separator and control unit 230 V 1 ∼ // 24 V ∼
Sophisticated technology with convincing suction power.
High-quality, robust drive motors, reliable continuous operation, great suction power within seconds, and flexible installation options.
Amazing power
The dry air suction systems by Dürr Dental are extremely powerful yet run really quietly. The V suction units are called dry systems because the aspirated substances are quickly guided into a separation/amalgam elimination unit. These components are integrated into the Dental Unit. Only dry air reaches the suction unit.
Seven to eight hours of continuous operation are not unusual. This places high demands on the technology. Dürr Dental V suction machines fulfil these requirements tirelessly. The contact-free, rotating turbine wheels generate the required vacuum and flow rate (suction power). A reliable electric motor enables non-stop operation. To reliably protect against condensated water, all models are fitted with a condensate separator as standard.
Model V 600 Voltage (V 1~/V 3~) 230/400 Frequency (Hz) 50/ 50/60 Current consumption (A) 5.0/ 1.8 – 4.5 Power (kW) 1.1/ 1.1 – 1.4 Speed (rpm) 2,850 Vacuum (mbar) with AAV 170 Cyclic duration factor (S1) 100% Noise level dB(A) approx. 63, with housing approx. 55
approx. 63, with housing 55Dimensions (H x W x D cm) 50 x 42 x 41
57 x 62 x 41 (with condensate separator)
50 x 49 x 53 (with housing)Weight (kg) 23, with housing 33
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 6000
Clinic Suction System
Group with 2 suction machines incl. control unit with vacuum controller and bacteria filter, remote monitoring possible.
For up to 30 workplaces with max. 20 operators at the same time.
Flexible solutions to meet your needs
Dürr Dental offers vacuum systems for dry and semi-dry suction systems. The flexible solutions are available in 6 variants and suitable for up to 100 treatment units. The integrated exhaust air bacteria filter only has to be changed every 3,500 hours. The power side channel compressors are precisely adjusted to the requriements by the intelligent PLC system.
High reliability, low power consumption
A sensor switches the custion motors on and off as required, allowing efficient use to be made of the electrical energy. The PLC system controls the equal use of the V machines, increasing their overall service lie and reliability. An electrical and mechanical auxiliary air valve provides additional cooling for the motots and a constant suction power.
Everything's under control thanks to the PLC system
Which suction motor is running? Momentary vacuum? Bakteria filter change? These questions are answered for the technician by the clinic display in the intelligent programmable logic controller. This allows him to monitor the complete suction or compressed air system at any time and to easily detect faults. The visualisation system from Dürr Dental even allows all the clinic systems to be remotely monitored.
Model V 6000 Voltage (V 3~) 400 Frequency (Hz) 50/60 Electrical power (kW) 5,6 / 7.4 Current consumption (A) 12,1 / 14,1 Dimensions (H x W x D cm) 115 x 130 x 130 Space requirements (H x W x D cm) 115 x 230 x 230 Weight (kg) 175 Vacuum (mbar) 160 Noise level dB(A) 73 without housing, 64 with housing Suction exhaust air connection (mm) 110/110 (DN 100)
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 900 S
The dry V Suction Systems
Up to 5 treatment positions, with 3 operators working simultaneously 230 V 1 ∼, 50 Hz, with condensate separator and control unit 230 V 1 ∼ // 24 V ∼
Sophisticated technology with convincing suction power.
High-quality, robust drive motors, reliable continuous operation, great suction power within seconds, and flexible installation options.
Amazing power
The dry air suction systems by Dürr Dental are extremely powerful yet run really quietly. The V suction units are called dry systems because the aspirated substances are quickly guided into a separation/amalgam elimination unit. These components are integrated into the Dental Unit. Only dry air reaches the suction unit.
Seven to eight hours of continuous operation are not unusual. This places high demands on the technology. Dürr Dental V suction machines fulfil these requirements tirelessly. The contact-free, rotating turbine wheels generate the required vacuum and flow rate (suction power). A reliable electric motor enables non-stop operation. To reliably protect against condensated water, all models are fitted with a condensate separator as standard.
Model V 900 S Voltage (V 1~/V 3~) 230/400 Frequency (Hz) 50 Current consumption (A) 6.3/3.6 Power (kW) 1.8/1.97 Speed (rpm) 2,850 Vacuum (mbar) with AAV 170 Cyclic duration factor (S1) 100% Noise level dB(A) approx. 65, with housing approx. 58 Dimensions (H x W x D cm) 52 x 42 x 42
57 x 62 x 42 (with condensate separator)
55 x 49 x 53 (with housing)Weight (kg) 33, with housing 49
SKU: n/a -
Equipment / Dental Unit / X-Ray / Etc, Suction
V 9000
Clinic Suction System
Group with 3 suction machines incl. control unit with vacuum controller and bacteria filter, remote monitoring possible.
For up to 50 workplaces with max. 30 operators at the same time.
Flexible solutions to meet your needs
Dürr Dental offers vacuum systems for dry and semi-dry suction systems. The flexible solutions are available in 6 variants and suitable for up to 100 treatment units. The integrated exhaust air bacteria filter only has to be changed every 3,500 hours. The power side channel compressors are precisely adjusted to the requriements by the intelligent PLC system.
High reliability, low power consumption
A sensor switches the custion motors on and off as required, allowing efficient use to be made of the electrical energy. The PLC system controls the equal use of the V machines, increasing their overall service lie and reliability. An electrical and mechanical auxiliary air valve provides additional cooling for the motots and a constant suction power.
Everything's under control thanks to the PLC system
Which suction motor is running? Momentary vacuum? Bakteria filter change? These questions are answered for the technician by the clinic display in the intelligent programmable logic controller. This allows him to monitor the complete suction or compressed air system at any time and to easily detect faults. The visualisation system from Dürr Dental even allows all the clinic systems to be remotely monitored.
Model V 9000 Voltage (V 3~) 400 Frequency (Hz) 50 / 60 Electrical power (kW) 8,2 / 10,9 Current consumption (A) 16,6 / 19,6 Dimensions (H x W x D cm) 115 x 130 x 130 Space requirements (H x W x D cm) 115 x 230 x 230 Weight (kg) 215 Vacuum (mbar) 160 Noise level dB(A) 75 without housing, 66 with housing Suction exhaust air connection (mm) 110/110 (DN 100)
SKU: n/a -
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area Models
V-Primer
Conservative Dentistry, Dental Simulator Education, Dental Training Products, Endodontics Area ModelsV-Primer
V-PRIMER is a one-component primer for precious metals (including Au/Ag/Pd alloys). It is based on the newly developed adhesive monomer called "VTD", a derivative of triazine-dithiol with acetone solvent. Simply coat precious alloy with V-PRIMER prior to application of Super-Bond to improve the durability of the bond. V-PRIMER eliminates the need for other bond-enhancing steps, such as heat treatment or tin plating.
- Simple treatment
- No more tin plating or heat treatment
- Can be used intraorally
SKU: n/a -
Endodontic Instrument / File, Endodontics, Rotary File
V-Taper Gold
V-Taper Gold, designed from advanced metallurgy, helps build smooth straight-line access and increases flexibility and cutting efficacy. Great taper design allows for large canal shaping.
- AF-R Wire tech for Shaping files
- AF-H Wire tech for Finishing Files
- 3 Shaping Files, 3 Finishing Files
- High elasticity of NITI Material
- Suitable for curved root canal preparation
- Specialty for variable taper 6 files design
SKU: n/a -
Impression Material, Materials / Medicament
Variotime
The right impression everytime.
The VPS precision impression material Variotime combines outstanding precision and process-oriented adaptability for excellent impressions as the base for precise-fitting prosthetics.
The innovative setting time concept features variable working time of 1:00 min – 2:30 min combined with an always short intraoral setting time of 2:30 min. 3 different delivery systems including automatic mixing as well as the compact allrounder system setup with 6 various viscosities enable easy, effi cient and safe processing of Variotime.
Variotime combines more than 25 years of Heraeus know-how in A-Silicones and experience with precision impression material.
- Crown and bridge impressions
- Inlay and onlay impressions
- Implant impressions
- Fixation and transfer impressions
- Functional impressions
SKU: n/a -
-
-
